• Type 1 to Type 2
• 7.2kW (32A, 1 Phase)
• 10 meters long
• IP55 rate
• Hand-held ergonomic design
EV Charging Cable Type 1 to Type 2 32A 1 Phase 10m
€231.11incl. VAT
Out of stock
Ask for product
With this EV Charging Cable Type 1 to Type 2 32A 1 Phase 10m, you can charge your EV/PHEV that has Type 1 port with an EV charging station that has Type 2 socket. The cable is 1 phase, can charge your EV up to 7.2 kW. The product has a nice appearance, a hand-held ergonomic design and is easy to plug. The working length is 10 meters and is made from thermoplastic material. It has protection level IP55, is anti-flaming, pressure-resistant, abrasion-resistant and impact resistant.
How to use EV charging cable Type 1 to Type 2:
We recommend to use the following steps:
1. Plug in the EV charging cable Type 2 male end of the cable to the charging station
2. Plug in the Type 1 end of the cable to the car’s charging socket
3. After the cable has clicked in place you are ready for the charge*
*Don’t forget to activate the charging station
When you finish with the charge, disconnect the vehicle side first and then the charging station side. Remove the cable from the charging station when not in use.
How to store:
This product is the lifeline of your electric vehicle and is important to keep it protected. Store the cable in a dry place preferably a storage bag. Moisture in the contacts will result in the cable not working. If this happens, place the cable in a warm and dry place for 24 hours. Avoid to leave the cable outside where sun, wind, dust and rain can get to it. Dust and dirt will result in the cable not charging. For longevity, ensure that your cable is not twisted or excessively bent during storage.
This product is very easy to use and store. The cable is designed for both outdoor and indoor charging and it has IP55 (Ingress Protection). This means that it has protection from dust and splash of water from any direction.
Safety notes:
- Always check the cable and the contacts for damage and contamination before using them.
- Never use a damaged product, vehicle inlet, or infrastructure socket outlet for charging.
- Never use contacts that are dirty or damp.
- Only connect the cable to vehicle inlets and infrastructure socket outlets that are protected against water, moisture and liquids.
- The charging process is finished when you actuate the locking lever of the vehicle connector. You can then disconnect the vehicle connector and the infrastructure plug. Never use force to disconnect them. Dangerous electric arcs could result in serious injury or death. Depending on the charging station and electric vehicle, the shutting down of the charging process and the duration of unlocking may vary.
- There are electric vehicles that can be started with the cable connected. Always make sure to disconnect it before driving away.
- In the unlikely event of smoke or melting, never touch the product. If possible, stop the charging process. Press the emergency stop switch on the charging station in any case.
- Make sure that the cable is out of reach of children. Only person’s with a valid driver’s license for motor vehicles can use it.
Specifications
| Weight | 4.2 kg |
|---|---|
| Plug Type | SAE J1772 (Type 1-Female) |
| Power Supply Plug | IEC 62196 (Type 2-Male) |
| Power | 7.2 kW |
| Maximum Current | 32 A |
| Power Supply | 1-Phase |
| Operational Voltage | 250 V/AC |
| Operational Temperature | -30 °C to +50 °C |
| SPEC | 3G6.0mm²+2×0.5mm² |
| Degree of Protection | IP55 |
| Vandalism-Proof | No |
| UV Resistant | Yes |
| Certificate | CE |
| Cable Material | Thermoplastic |
| Cable Length | 10 m |
| Manufacturer | EV+ |
| Warranty | 24 months |
Only logged in customers who have purchased this product may leave a review.
No files available for this product.
Related products
-
€192.39incl. VAT
-
€11.00incl. VAT
-
€231.11incl. VAT
-
€162.14incl. VAT
-
€200.86incl. VAT
-
€196.02incl. VAT
-
€188.76incl. VAT
-
€206.91incl. VAT
There are no reviews yet.